SSFP18N20 starmos t power mosfet extremely high dv/dt capability low gate charge qg results in simple drive requirement 100% avalanche tested gate charge minimized very low intrinsic capacitances very good manufacturing repeatability description starmos is a new generation of high voltage n?channel enhancement mode power mosfets. this new technology minimises the jfet effect, increases packing density and reduces the on-resistance. starmos also achieves faster switching speeds through optimised gate layout with planar stripe dmos technology. application switching application absolute maximum ratings parameter max. units i d @tc=25 ? c continuous drain current,v gs @10v 18 i d @tc=100 ? c continuous drain current,v gs @10v 11.4 i dm pulsed drain current 72 a p d @t c =25 ? c power dissipation 139 w linear derating factor 1.2 w/ ? c v gs gate-to-source voltage 30 v e as single pulse avalanche energy 216 mj i ar avalanche current 18 a e ar repetitive avalanche energy 13.9 mj dv/dt peak diode recovery dv/dt 5.0 v/ns t j t stg operating junction and storage temperature range C 55 to +150 soldering temperature, for 10 seconds 300(1.6mm from case) ? c mounting torque,6-32 or m3 screw 10 ibf in(1.1n m) thermal resistance parameter min. typ. max. units r jc junction-to-case 0.9 r cs case-to-sink,flat,greased surface 0.5 r ja junction-to-ambient 62.5 ? c/w pin1?gate pin2?drain pin1?source v dss = 200v i d25 = 18a r ds(on) = 0.18 1
SSFP18N20 starmos t power mosfet electrical characteristics @t j =25 ? c(unless otherwise specified) parameter min. typ. max. units test conditions v (br)dss drain-to-source breakdown voltage 200 v v gs =0v,i d = 250 a v (br)dss / t j breakdown voltage temp.coefficient 0.26 v/ ? c reference to 25 ? c,i d =1ma r ds(on) static drain-to-source on-resistance 0.18 v gs =10v,i d =9a v gs(th) gate threshold voltage 2.0 4.0 v v ds =v gs ,i d =250 a g fs forward transconductance 9.61 s v ds =40v,i d =9a 10 v ds =200v,v gs =0v i dss drain-to-source leakage current 100 a v ds =160v,v gs =0v,t j =150 ? c gate-to-source forward leakage 100 v gs =30v i gss gate-to-source reverse leakage -100 na v gs =-30v q g total gate charge 44 58 q gs gate-to-source charge 10.4 q gd gate-to-drain("miller") charge 27.1 nc i d =18a v ds =160v v gs =10v t d(on) turn-on delay time 17 40 t r rise time 16 40 t d(off) turn-off delay time 48 110 t f fall time 24 60 ns v dd =100v i d =18a r g =9.1 ? l d internal drain inductance 5.0 l s internal source inductance 13 nh between lead, 6mm(0.25in.) from package and center of die contact c iss input capacitance 1300 c oss output capacitance 400 c rss reverse transfer capacitance 130 pf v gs =0v v ds =25v f =1.0mh z source-drain ratings and characteristics parameter min. typ. max. units test conditions i s continuous source current . (body diode) 18 i sm pulsed source current . (body diode) 72 a mosfet symbol showing the integral reverse p-n junction diode. v sd diode forward voltage 1.5 v t j =25 ? c,i s =18a,v gs =0v t rr reverse recovery time 195 ns q rr reverse recovery charge 1.35 c t j =25 ? c,i f =18a di/dt=100a/ s t on forward turn-on time intrinsic turn-on time is negligible (turn-on is dominated by ls + l d ) notes: repetitive rating;pulse width limited by i sd 18a,di/dt 260a/ s,v dd v (br)dss , max.junction temperature(see figure 11) tj 25 ? c l = 1mh, ias = 18 a, vdd = 50v, pulse width 300 s; duty cycle 2% rg = 27 ? , starting tj = 25c 2
|